Kisker Biotech
0,00 €
0

Syringe Filters and Filter Plates

 
Syringe Filters

Our syringe filters are ultrasonic welded and certified DIN EN ISO 9001:2000. Not every filter is suitable for every application. In order to give you a rough overview of the application possibilities of our filters, we have put together an overview, by means of which you can make a preliminary selection of the membrane type contained in the filter.
Quality assurance: In order to comply with the highest demands with respect to the quality of our products, various standards are incorporated into our planning and production process.
The high-quality membranes are stored under the controlled conditions of the clean-room at constant air humidity in special containers, and stamped out and further processed from the roll material immediately before final assembly, in order to ensure the most homogenous possible membrane surface.
The production of the filter units is carried out under controlled conditions (clean-room class ISO 7). The components of the filter units are produced directly in our clean-room, where the largely automated final assembly and imprinting is also carried out.

During assembly, the filters are checked several times for any visible faults by means of sensors and a camera monitoring system. Following assembly, these are followed by the usual tests to the AQL standard, which monitor the bubble-point and the burst pressure of the filters. This checks the integrity of the membranes and connection of the membranes to the filter housing, together with the quality of the weld connection or edge-injection.


Technical Specification: 25 mm diameter (ultrasonic-welded):
  • Housing material: Polypropylene
  • Total filter volume: 0,6 ml
  • Dead volume: < 65 µl
  • Filter area: 490 mm2
  • Max. operating pressure: 6 bar
  • Inlet: Luer-Lock (female)

  • Outlet: Luer-Slip (male)


  • Technical Specification: 30 mm diameter (ultrasonic-welded):
  • Housing material: Polypropylene
  • Total filter volume: 0,864 ml
  • Dead volume: < 170 µl
  • Filter area: 707 mm2
  • Max. operating pressure: 6 bar
  • Inlet: Luer-Lock (female)

  • Outlet: Luer-Slip (male)


  •  
    Syringer Filter RC Membrane
    regenerated cellulose (low, unspecific adsorption for proteines)
    Aplications:
  • filtration of biological suspensions
  • HPLC-sample preparation
  • degasing of eluentes for HPLC (Bubble-Point on request, depending of pore size)
  • high resistance of the membrane to organic HPLC solvents (pH 3-12)

  • packaging unit 100 syringe filters
  • Cat. #DiameterPore SizeSteriltyEuroUnits
    SVF-RC-2502025 mm0,2 µno90,00
    SVF-RC-2504525 mm0,45 µno78,00
    SVF-RC-25020S25 mm0,2 µyes135,00
    SVF-RC-25045S25 mm0,45 µyes135,00
     
    Syringe Filter PTFE
    Membrane:
  • Polytetrafluorethylene (PTFE)

  • material is very inert and hydrophob, it can be changed to hydrophil by wedding with e. g. ethanol

  • Applications:
  • Filtration of aggressive chemicals, including acids and non water-based solvents
  • sample preparation for GC and HPLC
  • air- and gas-filtration
  • packaging unit 100 syringe filters
  • Cat. #DiameterPore SizeSteriltyEuroUnits
    SVF-PTFE-2502025 mm0,2 µno75,00
    SVF-PTFE-2504525 mm0,45 µno79,00
    SVF-PTFE-25020S25 mm0,2 µyes99,00
    SVF-PTFE-25045S25 mm0,45 µyes99,00
     
    Syringe Filter CA
    Membrane: Celluloseacetat (hydrophilic, low protein adsorption, high temperature stability) Applications:
  • filtration of biological samples (e. g. enzymes, biological macromolecules)

  • packaging unit 100 filters
  • Cat. #DiameterPore SizeSteriltyEuroUnits
    SVF-CA-2502025 mm0,2 µno62,00
    SVF-CA-2504525 mm0,45 µno62,00
    SVF-CA-25020S25 mm0,2 µyes95,00
    SVF-CA-25045S25 mm0,45 µyes95,00
    SVF-CA-3002030 mm0,2 µno109,00
    SVF-CA-3004530 mm0,45 µno109,00
    SVF-CA-30020S30 mm0,2 µyes135,00
    SVF-CA-30045S30 mm0,45 µyes135,00
    back to top


    İ 1999 - 2011 Dipl. oec. troph. Gerlinde Kisker